Pipe Cutting and Beveling Machine

Pipe Cutting and Beveling Machines

Each H&M machine is constructed of durable lightweight , hard-anodized aluminum for easy transportation to any job site for cutting and beveling 2" - 48" - diameter pipe precisely, quickly and economically, even under the toughest conditions.

Every ring gear and saddle are precisely machined and calibrated to .025in concentricity and .015 in squareness. The standard rear-mounted short saddle aids cutting and beveling in tight locations, while allowing precise back-beveling operations.

H&M's Unique "split horseshoe" design permits easy placement over pipe sections. A quick-operating boomer assembly securely locks the machine to the pipe for an entire 360 -degree rotation. No repositioning is ever needed! H&M's patented Cuboid Spacer System keeps the spacers on the machine to minimize downtime.

H&M Pipe Beveling Machine save weld prep time and money compared to hand cutting. With easy-to-follow manual and a few minutes of instruction, any operator can easily make accurate cuts and bevel.

H&M Exclusive Standard Features

Cuboid Spacer System H&M patented Cuboid Spacer System relieves frustration and downtime in looking for lost spacers, because the spacers never leave the machine.

The H&M Cuboid is a six-sided form with rectangular sides. Three specific thickness conform to different pipe size. Only four Cuboid spacers are used to quickly set up the machine. In the past 12 spacers were required.

The saddle of each H&M machine and the four cuboids allow four specific pipe size to be cut or bevel. each side of every cuboid spacer is clearly stamped to ensure cutting the correct pipe size. When not in use the cuboid spacers are securely housed on the back of the saddle. It's a no-lose proposition in timesaving productivity !

Improved Saddle Design

H&M achieves functional and financial advantages for the customer over its competition by designing the precision saddle and ring gear as separate components.

Instead of locating the ring gear in the middle H&M places the saddle behind the ring gear.

H&M Saddle Assembly is less likely to be damaged; however, if a problem occurs, this separate component design is more economical in replacement cost.

7CS Solid Torch Holder

Now Standard on all H&M's saddle-type beveling machine, the Model "C" Adjustable Torch Holder, the Model "C" Out-of-Round Attachment and all Shape Cutting Attachment, the 7CS Solid Torch Holder provides greater cutting accuracy, efficiency and strength. A single thumbscrew secures the torch instead of hose clamp. A cotter pin makes the thumbscrew captive to the torch holder, allowing easy removal or replacement of the torch. Precise and simple to use, the 7CS means solid performance. "Note": The 7CS is available for retrofitting to H&M's 5C Torch Carrier Assembly. Only two screws are needed for removal and replacement.

2DH Boomer Strap Eye Assembly

Forget cotter pins and S-Hooks. H&M offers a safer, more dependable 2DH Boomer Strap Eye Assembly. The 2DH allows the chain on the boomer assembly to quickly adjust and securely lock the machine to its respective pipe size. The boomer assembly is now a captive member of the machine.

H&M Accessories "Motorized Kits"

For large pipe work or fabrication H&M highly recommends its motorized kits. H&M Motorized kits achieve precise torch speed, increased production and consistent, high-quality beveled edges with every cutting and beveling operation. Speed ranges are sufficient for most plasma cutting applications.

Torch Valve Manifold Block (TVMB)

H&M's Torch Valve Manifold Block saves time and energy in accurate torch settings without wasting oxygen and fuel gas. With the TVMB just adjust the torch once. A lever turn the torch on and off without altering the flame setting. Consistent, uniform, high-quality flame-cut bevel from end to end are achieved every time! The TVMB also eliminates hose drag for even greater accuracy and productivity.

Double Torch Holder

Increase production by 100% with H&M Double Torch holder! It consists of one 18" torch arm with two 5C Torch Carrier Assemblies. After positioning the torch holder at a specific bevel angle, two beveled cuts can be made in one revolution. Note: For ultimate precision and control, use of the Double Torch Holder in conjunction with the optional TVMB is Strongly advised.

Storage Boxes

The best protection for your H&M machine during transportation and storage is the lightweight aluminum storage box. Storage boxes for all H&M Models No.0 through No.6 Standard Beveling Machines are available.

Model "C" Adjustable Torch Holder

Both horizontal and vertical torch movements are easily made by the Model "C" Adjustable Torch Holder with its two rack-and-pinion-driven, dove-tailed slide assemblies. Smooth, accurate torch adjustments eliminate blow holes. Even the torch height can be changed while the cutting torch is in motion.

No special modifications are needed with most torch lengths. A built-in protractor provides precise bevel angle every time. The Model "C" fits all Standard H&M Beveling Machines, except Model No. 0, which requires a special adaptor plate.

Model "C" Out-of-Round Attachment

Cut and bevel imperfect pipe and create square ends without a problem with H&M's Model "C" Out-of-Round Attachment. Riding on outside diameter of the pipe, the Model "C" compensates for errors in roundness by using a spring-loaded, dovetailed slide.

Like the Model 'C" Torch Holder, the Out-of-Round features the same precise assemblies for independent horizontal and vertical torch movements. A built-in protractor provides precise forward- or back-beveling angle settings.

The Model 'C" Out-of-Round Attachment fits all H&M Standard Beveling Machines that cut and bevel 3" to 48" pipe. The Model No. 0 requires a special adaptor when working 2" - 4" pipe.

Shape Cutting Attachment and Templates

Even novices to pipe cutting and beveling can archive superior-quality craftsmanship in making saddles, Y's, T's, miters and various angle cuts on all H&M machines with shape cutting attachments and templates.

Each custom-made, H&M prefabricated metal template is bolted to the face of the ring gear. the torch is spring-loaded against the template. While the machine rotates around the pipe, the torch moves along the same path as the template. The triangular design of hard-anodized travel tube and carriage rollers ensures lateral torch stability and smooth. consistent, horizontal torch travel during a complete revolution. Achieve accurate cuts from proven patterns every time, even when cutting miters up to 45 degrees.

 

 

 

Copyright 2014 JTS-PTA ©